Horizontal Single Casing Good Performance Of NPSH Gravel Pump 12 /
10 G-G
Product Introduction
1. Horizontal, single pump housing centrifugal pump.
2. The pump body and the pump cover are clamped by a special clamp.
The discharge direction of the pump can be at any position of 360
degrees, which is convenient to install and use.
3. The bearing assembly of the pump adopts a cylindrical structure,
which is convenient for adjusting the gap between the impeller and
the pump body, and can be completely removed during maintenance.
The bearings are greased.
4. The shaft seal form of the pump has packing seal, impeller seal
and mechanical seal.
5. The pump flow path is wide, the cavitation performance is good,
the efficiency is high, and the wear resistance is improved.
6. Transmission mode mainly includes V-type V-belt drive, flexible
coupling drive, gear reducer drive, hydraulic coupling drive,
variable frequency drive, thyristor speed control, etc.
7. The material of the over-current component is made of
high-hardness wear-resistant alloy cast iron.
8. Using a variety of speeds and a variety of variants, so that the
pump operates under a variety of conditions. Long service life and
high operating efficiency can meet a variety of harsh conveying
conditions. 9. GH pump is a high lift pump. It is mainly used for
continuous conveying of strong abrasive materials that cannot be
transported due to the large size of the slurry.
Application
-dredging
-sifting gravel
-dredging rivers
-mining
-metal smelting
-blasting
Type meaning for dredge pump
12/10G-G(H)
12----------------Suction Diameter (inch )
10----------------Discharge Diameter (inch)
G-----------------Support Type
G-----------------Pump Model
H-----------------Gravel Pump High Head
G(H) gravel pump material list for parts:
| Part Name | Material | Specification | HRC | Application | OEM Code |
| Bowl, door, back liner & impeller | Metal | AB27: 23%-30% chrome white iron | ≥56 | Used for higher wear condition with pH between 5 and 12 | A05 |
| AB15: 14%-18% chrome white iron | ≥59 | Used for higher wear condition | A07 |
| AB29: 27%-29% chrome white iron | 43 | Used for lower pH condition especially for FGD. It also can be used
for low-sour condition and desulfuriation installation with pH not
less than 4 | A49 |
| AB33: 33%-37% chrome white iron | | It can transport oxygenated slurry with pH not be less than 1 such
as phospor-plaster, nitric acid, vil, phosphate etc. | A33 |
| Expeller & expeller ring | Metal | B27: 23%-30% chrome white iron | ≥56 | Used for higher wear condition with pH between 5 and 12 | A05 |
| Grey iron | | | G01 |
| Stuffing Box | Metal | AB27: 23%-30% chrome white iron | ≥56 | Used for higher wear condition with pH between 5 and 12 | A05 |
| Grey iron | | | G01 |
| Door clamp plate, bearing house & base | Metal | Grey iron | | | G01 |
| Ductile iron | | | D21 |
| Shaft | Metal | Carbon steel | | | E05 |
| Shaft sleeve, lantern ring/resctrictor, neck ring, gland bolt | Stainless steel | 4Cr13 | | | C21 |
| 304 SS | | | C22 |
| 316 SS | | | C23 |
| Joint rings & seals | Rubber | Butyl | | | S21 |
| EPDM rubber | | | S01 |
| Nitrile | | | S10 |
| Hypalon | | | S31 |
| Neoprene | | | S44/S42 |
| Viton | | | S50 |
Performance table:
| Pump Model | Allowable | Clear Water Performance | |
| Max. Power | Capacity Q | Head | Speed | Max.Eff. | Impeller. Dia. (mm) |
| (kw) | m3/h | H (m) | n(r/min) | (%) |
| 6/4D-G | 60 | 36-250 | 5-52 | 600-1400 | 58 | 378 |
| 8/6E-G | 120 | 126-576 | 6-45 | 800-1400 | 60 | 378 |
| 10/8S-G | 560 | 216-936 | 8-52 | 500-1000 | 65 | 533 |
| 10/8F-G | 260 | 216-936 | 8-52 | 500-1000 | 65 | 533 |
| 10/8S-GH | 560 | 180-1440 | 24-80 | 500-950 | 72 | 711 |
| 12/10F-G | 260 | 360-1440 | 10-60 | 400-850 | 65 | 667 |
| 12/10G-G | 600 | 360-1440 | 10-60 | 400-850 | 65 | 667 |
| 12/10G-GH | 600 | 288-2808 | 16-80 | 350-700 | 73 | 950 |
| 14/12G-G | 600 | 576-3024 | 8-70 | 300-700 | 68 | 864 |
| 16/14G-G | 600 | 720-3600 | 18-44 | 300-500 | 70 | 1016 |
| 16/14TU-G | 1200 | 324-3600 | 26-70 | 300-500 | 72 | 1270 |
| 18/16G-G | 600 | 720-4320 | 12-48 | 250-500 | 72 | 1067 |
| 18/16TU-G | 1200 | 720-4320 | 12-48 | 250-500 | 72 | 1067 |
Construction Drawing
Selection & Performance Chart
